Advanced Search

Journal Navigation

Journal Home

Subscriptions

Archive

Contact Us

Table of Contents

CiteULike is a free service for managing and discovering scholarly references - click here to get started.

Sign In to gain access to subscriptions and/or personal tools.
Journal of Dental Research
This Article
Right arrow Full Text (PDF)
Right arrow References
Right arrow Alert me when this article is cited
Right arrow Alert me if a correction is posted
Right arrow Citation Map
Services
Right arrow Email this article to a friend
Right arrow Similar articles in this journal
Right arrow Similar articles in PubMed
Right arrow Alert me to new issues of the journal
Right arrow Add to Saved Citations
Right arrow Download to citation manager
Right arrowRequest Permissions
Right arrow Request Reprints
Right arrow Add to My Marked Citations
Citing Articles
Right arrow Citing Articles via HighWire
Right arrow Citing Articles via Google Scholar
Right arrow Citing Articles via Scopus
Google Scholar
Right arrow Articles by Papadogiannis, Y.
Right arrow Articles by Lakes, R.S.
Right arrow Search for Related Content
PubMed
Right arrow PubMed Citation
Right arrow Articles by Papadogiannis, Y.
Right arrow Articles by Lakes, R.S.
Right arrowPubmed/NCBI databases
*Substance via MeSH
Social Bookmarking
Add to CiteULike   Add to Complore   Add to Connotea   Add to Del.icio.us   Add to Digg   Add to Reddit   Add to Technorati   Add to Twitter  
What's this?

Creep of Amalgam at Low Stresses

Y. Papadogiannis

Department of Operative Dentistry, Aristotelian University, Thessaloniki, Greece

D.B. Boyer

Department of Operative Dentistry, University of Iowa, Iowa City, Iowa 52242

R.S. Lakes

Department of Biomedical Engineering, University of Iowa, Iowa City, Iowa 52242

The creep and recovery, of dental amalgam were studied with a torsional creep apparatus. The purpose was to investigate viscoelastic behavior in a low stress range that might result from normal chewing forces. The creep of specimens up to six months old was also studied. Four types of alloys for amalgam were used: two single-composition sphericals (SCS), an admixture-lathe-cut eutectic (ALE), and a conventional (CON). Constant torque was applied to dumbbell-shaped specimens for three hr and, after the stress was released, recovery was followed for 50 hr. All measurements were made in water at 37°C after storage of the specimens for one week in 37°C water. Creep was also measured at nine intervals an specimens aged from three hr to six months. The SCS amalgams exhibited the least amount of creep, followed by the ALE amalgam. The CON amalgam had the highest creep. The SCS amalgams approached linear viscoelastic behavior in the shear stress range of 0.78-4. 10 MPa at 37°C. They did not exhibit steady-state (viscous) creep at stresses less than 4.10 MPa. Recovery was complete but proceeded more slowly than creep. The ALE and CON amalgams exhibited viscous creep at 1.23 MPa and higher. The steady-state creep rate depended on stress, and the stress exponent ranged from 2.3-3.5, All except the ALE amalgam showed essentially constant creep compliance when aged up to six months, once the amalgamation reaction was completed after 24 to 48 hr. The compliance of the ALE amalgam gradually decreased over the six-month period.

Journal of Dental Research, Vol. 66, No. 10, 1569-1575 (1987)
DOI: 10.1177/00220345870660101101
Add to CiteULike CiteULike   Add to Complore Complore   Add to Connotea Connotea   Add to Del.icio.us Del.icio.us   Add to Digg Digg   Add to Reddit Reddit   Add to Technorati Technorati   Add to Twitter Twitter    What's this?


This article has been cited by other articles:


Home page
 JDRHome page
H.H.K. Xu, H. Liao, and F.C. Eichmiller
Indentation Creep Behavior of a Direct-filling Silver Alternative to Amalgam
Journal of Dental Research, December 1, 1998; 77(12): 1991 - 1998.
[Abstract] [PDF]